BORNIT® Unibit
bitumen | coating | solvent-free | protection | soil moisture
Short information
- solvent-free alternative to traditional coatings
- bitumen coating for renovation work on bituminous topcoats
- for the protection of concrete, plaster and masonry
- protective coating against soil moisture
- can also be used as an adhesion-enhancing primer when diluted with water
- can be brushed or sprayed-on
Product
Colour
Content
sufficient for:
Item
EAN code
euro pallet
approx. 8.3 m²
6900002662
4 017228 00280 4
60 bucket
sufficient for:
Item
EAN code
euro pallet
approx. 16.5 m²
6900002531
4 017228 00288 0
44 bucket
sufficient for:
Item
EAN code
euro pallet
approx. 41.5 m²
6900002661
4 017228 00284 2
18 bucket
Consumption
- as primer diluted 1:2 with water: approx. 0.10 l/m²
- as covering protective coat (at least 2 coats) and under BORNIT® BORNIthene Plus: approx. 0.30 l/m² (per coat)
Storage note
- at moderate temperatures, not below +2 °C up to +30 °C, sensitive to frost!
- in originally sealed containers storable for 12 months
Complementary products
PrimingCleaningFollow-up products
Wetting tools with water before use considerably extends their service life!
status technical data sheet
25th November 2020
Areas of application
BORNIT® Unibit serves as protective and waterproofing coating for concrete, plaster and masonry against ground moisture (not for building structure waterproofing according to DIN 18533) as well as topcoat upon restoration of bituminous roof membranes. Furthermore, BORNIT® Unibit is used for protection against moisture on concrete elements (shafts, channels, etc.) in the area in contact with the ground. Not suitable for corrugated bituminous sheets.
BORNIT® Unibit can be used diluted with water 1:2 as adhesion-improving primer for all BORNIT® bitumen emulsion products as well as undiluted as primer for BORNIT® BORNIthene Plus.
BORNIT® Unibit can be used diluted with water 1:2 as adhesion-improving primer for all BORNIT® bitumen emulsion products as well as undiluted as primer for BORNIT® BORNIthene Plus.
Type and properties
BORNIT® Unibit is a universally applicable, solvent-free and latex-modified bitumen emulsion. BORNIT® Unibit can be used undiluted as a protective coating for a wide variety of standard building substrates and diluted with water as a primer for bitumen emulsion products.
The product can be applied by brush, roller or airless spraying.
BORNIT® Unibit is QNG-compliant in accordance with QNG requirements catalogue appendix document 313.
The product can be applied by brush, roller or airless spraying.
BORNIT® Unibit is QNG-compliant in accordance with QNG requirements catalogue appendix document 313.
Advantages
- easiest handling, since manufactured ready for use
- universally applicable, thus numerous uses
- free from solvents, hence environmentally friendly
- economical and cost-cutting, due to low equipment and material costs and effort
Surface
The substrate must be firm, clean and free from separating substances (oils, greases, etc.). It may be slightly moist, but not wet. In case of highly absorbent substrates, prime with BORNIT® Grundbit.
Processing
BORNIT® Unibit is delivered ready for use.
Topcoats must be applied undiluted. For that, at least 2 coats are recommended. The second coat is applied after sufficient surface drying of the first one.
The product is applied with a moistened coating broom or brush, resp., or airless spraying equipment.
Clean the respective processing equipment with water immediately after use. Hardened material can be removed with BORNIT® Bitumen Cleaner.
For use as a primer, BORNIT® Unibit is diluted 1:2 with fresh tap water under stirring and mixed well with a mechanical stirrer.
BORNIT® Unibit must only be applied in dry weather and under no circumstances in case of frost or rain or impending rain, resp.
Topcoats must be applied undiluted. For that, at least 2 coats are recommended. The second coat is applied after sufficient surface drying of the first one.
The product is applied with a moistened coating broom or brush, resp., or airless spraying equipment.
Clean the respective processing equipment with water immediately after use. Hardened material can be removed with BORNIT® Bitumen Cleaner.
For use as a primer, BORNIT® Unibit is diluted 1:2 with fresh tap water under stirring and mixed well with a mechanical stirrer.
BORNIT® Unibit must only be applied in dry weather and under no circumstances in case of frost or rain or impending rain, resp.
Consumption
as primer diluted 1:2 with water: approx. 0.10 l/m²
as covering protective coat (at least 2 coats) and under BORNIT® BORNIthene Plus: approx. 0.30 l/m² (per coat)
as covering protective coat (at least 2 coats) and under BORNIT® BORNIthene Plus: approx. 0.30 l/m² (per coat)
Product data in brief
Product type
latex-modified bitumen emulsion
Base
bitumen emulsion, latex
Solvent
water
Density at +20 °C
approx. 1.00 g/cm³
PH-value
11.0 - 11.5
Consistency
viscous
Film-forming components
min. 55 %
colour(s)
black-brown
Dilution
water
Application
small or large brush, roller, spraying equipment (airless)
Processing temperature (ambient and substrate)
not below +5 °C and not above +30 °C
Cleaning
in the fresh state with water, in the hardened state with BORNIT® MultiClean Spray, BORNIT® MultiClean or BORNIT® Bitumen Cleaner
storage
at moderate temperatures, not below +2 °C up to +30 °C, sensitive to frost!
Shelf life
in originally sealed containers storable for 12 months
GISCODE
BBP10
GISCODE link comp. A
https://www.wingisonline.de/showbetrandoc.aspx?gisbaunr=4/00000018210/000009&docid=1995&lang=de
Substances hazardous to health in terms of the ordinance on hazardous materials
none
Hazard class according to ADR
none
Boiling start and Boiling range
+100 °C
Health and fire protection, occupational safety
To ensure safe handling of the product, the physical, safety, toxicological and ecological information provided online, the information in the current safety data sheet and the additional information on the label must be read and followed before purchasing or using the product! The applicable regulations, ordinances and laws must be complied with.
In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.
In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.
Storage
In originally sealed containers storable for 12 months. Protect from frost!
Disposal note
Only recycle completely empty containers. Material residues can be disposed of according to AVV-ASN: 080410 (adhesive and sealing compound residues, except for those falling under 080409).
Note
The above information replaces all previous technical information about the product. Thus, this information is no longer valid. The details have been compiled according to the latest state of application technology. Please observe, however, that, depending on the state of the construction object, deviations from the method of application suggested in the datasheet may be required. Unless agreed otherwise in individual contracts, any information contained in the datasheet shall be non-binding and thus does not represent an agreed product constitution. We reserve the right to any changes in the information contained in this datasheet anytime.
® Unibit, coating, solvent-free, protection, ground moisture">
® Unibit, coating, solvent-free, protection, ground moisture">GISCODE
BBP10
UN-number
No dangerous good in sense of these transport regulations.
Hazard-determining components for labelling
1.2-Benzisothiazol-3(2H)-on
EUH-records
EUH208: Contains 1,2-Benzisothiazol-3(2H)-on. May produce an allergic reaction.
Recommended, personal protective equipment:
