155

BORNIT® Bitumen Joint Sealant 2C

bitumen | crack repair | cracks | joints | seams
BORNIT
short information
  • solvent-free
  • for sealing of cracks, seams, joints in asphalt and concrete surfaces
  • for gluing of marker buttons
  • permanently elastic
  • heat and cold resistant
product
colour
content
Bitumen Joint Sealant 2C
black
360 ml / cartridge
sufficient for:
item
EAN code
box
approx. 14 m (at 5 x 5 mm)
6800000345
4 017228 00257 6
12 cartridge
consumption
approx. 14 m/cartridge for a joint cross-section of 5x5 mm
storage note
  • not sensitive to frost
  • in originally sealed containers storable for 12 months

status technical data sheet
27 November 2020

areas of application
BORNIT® Bitumen Joint Sealant 2C is used for sealing cracks and open seams in asphalt surfaces as well as for fixing retroflecting road studs on asphalt.

type and properties
BORNIT® Bitumen Joint Sealant 2C is a 2-component, bituminous crack sealing compound.
It is permanently elastic, has excellent resistance to heat and cold, is ageing- and weather-resistant, adheres very well to asphalt surfaces and has a low surface tackiness. The thorough hardening time at +25 °C is approx. 1 hour.

advantages
  • can be processed cold and ready to use
  • no mixing times
  • fast curing and resilient
  • can be installed by one person with little effort on the equipment
  • long shelf life (12 months)

surface
The substrate must be clean, firm and dry as well as free from any loose particles and adhering contamination.

processing
The flanks of the joint or the crack, resp., must be cleaned and primed with BORNIT® Hot Compound Primer Fix. The cartridge is inserted into the BORNIT® Cartridge Gun. The safety cap is removed from the cartridge and the enclosed mixing tube screwed on. Depending on the crack width, the mixing tube can be shortened to thus achieve a larger outlet opening. BORNIT® Bitumen Joint Sealant 2C must be processed within approx. 15 minutes.

Processing temperature
The outside temperature during processing BORNIT® Bitumen Joint Sealant 2C must not be below +5 °C and not above +30 °C. Processing must be undertaken in dry weather.
The temperature of BORNIT® Bitumen Joint Sealant 2C must be at least +10 °C. The asphalt surface temperature must be > +5 °C. If necessary, the crack or the seam, resp., can be carefully preheated with hot air.

consumption
approx. 14 m/cartridge for a joint cross-section of 5x5 mm

product data in brief
product type
bitumen
base
bitumen
density at +20 °C
1,15 - 1,20 g/cm³
consistency
pasty
colour(s)
black
dimensions
cartridge: W x L = 63 x 220 mm
application
special cartridge gun
processing time
approx. 15 minutes
thorough hardening time
approx. 1 hour
storage
not sensitive to frost
shelf life
in originally sealed containers storable for 12 months
hazard class according to ADR
keine
flash point
200,0
health and fire protection, occupational safety
To ensure safe handling of the product, the physical, safety, toxicological and ecological information provided online, the information in the current safety data sheet and the additional information on the label must be read and followed before purchasing or using the product! The applicable regulations, ordinances and laws must be complied with.

In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.

storage
The product can be stored for 12 months in the original, closed container. BORNIT®- Bitumen Joint Sealant 2C is to be stored dry and cool.

disposal note
Only recycle completely empty containers. Material residues can be disposed of according to AVV-ASN: 170302 (adhesive and sealant residues, except for those falling under 170302).

note
The above information replaces all previous technical information about the product. Thus, this information is no longer valid. The details have been compiled according to the latest state of application technology. Please observe, however, that, depending on the state of the construction object, deviations from the method of application suggested in the datasheet may be required. Unless agreed otherwise in individual contracts, any information contained in the datasheet shall be non-binding and thus does not represent an agreed product constitution. We reserve the right to any changes in the information contained in this datasheet anytime.
BORNIT<sup class=® Bitumen Joint Sealant 2C, crack, joint, seam, seal, asphalt, concrete">
BORNIT<sup class=® Bitumen Joint Sealant 2C, crack, joint, seam, seal, asphalt, concrete">
UN-number
Kein Gefahrgut im Sinne der Transportvorschriften.