BORNIT® Cold Sealing Compound
joint sealant | joint sealing | weather and aging resistant

- 2-component, polysulfide based jointing material
- for permanently sealing of horizontal concrete and asphalt joints
- for expansion joints up to 35% of the joint width
- can be poured-on, self-levelling
- UV- and fuel resistant
euro pallet
30 box
euro pallet
18 box
euro pallet
30 box
euro pallet
18 box
- dry, cool (below +25 °C)
- in originally sealed containers storable for 12 months
BORNIT® Cold Sealing Compound reliably seals joints against the penetration of water pollutants into the ground. It is particularly suitable for sealing joints in road, bridge and tunnel construction.
BORNIT® Cold Sealing Compound is suitable for sealing floor or ground-level joints between concrete elements as well as concrete components and asphalt surfaces subject to mechanical stresses (vehicle and pedestrian traffic), chemical stresses from de-icing salts and temperature-dependent movements of the components. Upon use in concrete surfaces, BORNIT® Cold Sealing Compound can also be subjected to chemical stresses from fuels. In connection with BORNIT® Concrete or Asphalt Primer, resp., as adhesive primer and with respective structural joint design, horizontal joints of most different construction materials in civil engineering and road construction can be permanently sealed.
BORNIT® Cold Sealing Compound (self-levelling) can be used up to an inclination of the joints of max. 3 %. Joints with a higher inclination or vertical joints should be sealed with the stable BORNIT® Cold Joint Sealant. The joint sealant must not be used for joints, which are permanently under the surface of liquids (e.g. in swimming pools, clarification tanks) or are exposed to strongly oxidising acids and bases, as well as for joints in facilities for storing, filling and transhipping of water pollutants (called LAU plants).
It is pourable and self-levelling. In the hardened state, BORNIT® Cold Sealing Compound results in elastic joint sealing with very good resistance to weather impacts and ageing and high mechanical strength.
BORNIT® Cold Sealing Compound complies with DIN EN 14188-2.
- very flexible
- waterproof and UV-resistant
- universally applicable
- less equipment, material and labor required for processing
In concrete joints,
the fusion faces must be primed with BORNIT® Concrete Primer. The components A and B are thoroughly mixed and the primer is evenly applied with a brush. Following a flash-off time of 30 min to 2 hours (depending on the temperature), the sealant can be applied. BORNIT® Concrete Primer should not have completely dried off. If more than 24 hours should have passed, the primer layer must be roughened and new primer applied.
or
In asphalt joints,
the fusion faces must be primed with BORNIT® Asphalt Primer.nThe asphalt joints must be freshly cut, since otherwise adhesion problems occur. The components A and B are thoroughly mixed and the primer is evenly applied with a brush. Following a flash-off time of 2 to 6 hours (component temperature > +25 °C approx. 2 hours, < +10 °C approx. 6 hours), the sealant can be applied. The asphalt primer should have dried off as far as possible. It must be observed that no moisture film has formed on the primer surface due to undercutting of the dew point.
BORNIT® Cold Sealing Compound is packaged separately in various containers. The B component is added to the A component and mixed using a paddle mixer until there are no more colour streaks. In order to avoid the formation of bubbles, it must be observed that no air is mixed into the product.
The joint sealant is inserted into the joint with suitable tools (e.g. manual or compressed-air guns). It is self-levelling. Possibly ascending air bubbles must be removed within the processing time by slight smoothing the surface with a soft flat brush or smoothing stick. The temperature of the sealant prior to mixing should be min. +10 °C. The component temperature must not be below +5 °C and not above +40 °C.
Until reaching the full load-bearing capacity, a thorough hardening time of at least 48 hours at +20 °C of ground and material temperature must be complied with.
Product data in brief
Component B: n.a.
Component B:
In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.


BORNIT-Werk Aschenborn GmbH
Reichenbacher Straße 117
08056 Zwickau / Germany
2009
1290-1416/2025
DIN EN 14188-2:2004
System: Two-component (M) / Type: Self-levelling (sl)
Cold workable polysulphide-based joint sealant
Adhesive capacity and expansibility | Tensile modulus at 100 % expansion: at +23 °C ≥ 0.15 MPa, at -20 °C ≤ 0.6 MPa |
Adhesive capacity | No failure at -20 °C ≤ 0.6 MPa |
Water impermeability | Resilience ≥ 70 %, Loss in volume ≤ 5 % |
Resistance to deformation | Resilience ≥ 70 %, Loss in volume ≤ 5 % |
Durability of water impermeability when exposed to chemicals | Passed |
Durability of all mandated properties against ageing | Change in the tensile modulus at 100 % expansion: ≤ ± 20 % |
Flame resistance | Passed |
UFI P030-V0WY-K00Q-YCN9
- How much: as exact a quantity as possible
- Who: Age, weight, sex and condition of the person(s) concerned.
- When: Time of the event
- Where: Place of occurrence
- How: ingestion, inhalation, skin contact, etc.
Component A
P501: Dispose of contents/container to a suitable recycling or disposal facility.
Component B
H411: Toxic to aquatic life with long lasting effects.
P270: Do not eat, drink or smoke when using this product.
P273: Avoid release to the environment.
P301 + P312: IF SWALLOWED: Call a POISON CENTRE or doctor if you feel unwell.
P330: Rinse mouth.
P391: Collect spillage.
P501: Dispose of contents/container to a suitable recycling or disposal facility.