BORNIT® Corrosion Preventer

bitumen | metal | protection | corrosion | rust
short information
  • solvent-based bitumen protective coating
  • against metal corrosion
  • protects metal
  • reliably against rust and against diluted, non-oxidizing acids, flue gases and vapors
  • resistant to chemicals
Corrosion Preventer
10 ltr. / bucket
sufficient for:
EAN code
euro pallet
approx. 25 m²
4 017228 004655
45 bucket
Corrosion Preventer
25 ltr. / bucket
sufficient for:
EAN code
euro pallet
approx. 62.5 m²
4 017228 004662
18 bucket
approx. 0.4 l/m² per coat (2 coats recommended)
storage note
  • at least +5 °C
  • product is not sensitive to frost
  • in originally sealed containers storable for 12 months

status technical data sheet
12 November 2020

areas of application
BORNIT® Corrosion Preventer is suitable as a corrosion protection coating material for waggon undercarriages, bridges and steel structures. BORNIT® Corrosion Preventer reliably protects concrete, masonry, plaster and metal from diluted, non-oxidising acids, flue gasses and vapours, e.g. in the chemicals and textiles industries.

type and properties
BORNIT® Corrosion Preventer is a bitumen-based sealing and finishing material protecting surfaces from corrosion.

  • high penetrating capability into the substrate
  • easiest handling, since manufactured ready for use
  • universally applicable, therefore numerous uses
  • good adhesive properties due to white spirit content
  • economical and cost-cutting, due to low equipment and material costs and effort

The substrate must be clean, dry, rust- and grease-free. Use BORNIT® Bitumen Primer for priming.

BORNIT® Corrosion Preventer is spreadable and sprayable without dilution. Stir up BORNIT® Corrosion Preventer prior to processing! It is recommended to apply two coats. The processing temperature (ambient and substrate temperature) should not be below +5 °C and not above +35 °C.
Do not use in closed rooms!

approx. 0.4 l/m² per coat (2 coats recommended)

product data in brief
product type
bituminous corrosion protection coating
bitumen, solvent
white spirit
density at +20 °C
0.91 - 0.93 g/cm³
spreadable, sprayable
film-forming components
min. 60 %
small or large brush, spraying equipment (airless)
processing temperature (ambient and substrate)
mind. +5 °C und max. +35 °C
thorough hardening time
max. 8 hours at +20 °C
BORNIT® MultiClean Spray, BORNIT® MultiClean, BORNIT® Bitumen Cleaner
at least +5 °C product is not sensitive to frost
shelf life
in originally sealed containers storable for 12 months
GISCODE link comp. A
VOC category
2004/42/EG g/Lb/: 350 g/ltr.
actual permissible VOC content
< 350 g/ltr.
hazard class according to ADR
Flammable liquids (Flam. Liq. 3)
Acc. to Industrial Safety Regulation (BetrSichV)
boiling start and Boiling range
> +150 °C
upper/lower explosion limit
6,4 - 0,67 Vol-%
flash point
36.0 °C
health and fire protection, occupational safety
Caution - Only use in well-ventilated outdoor areas. Not suitable for use in closed rooms or poorly ventilated pits!
Do not eat, drink or smoke while working, keep away from sources of ignition.

To ensure safe handling of the product, the physical, safety, toxicological and ecological information provided online, the information in the current safety data sheet and the additional information on the label must be read and followed before purchasing or using the product! The applicable regulations, ordinances and laws must be complied with.

In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.

In originally sealed containers storable for 12 months. The product is not sensitive to frost!

disposal note
Only recycle completely empty containers. Material residues can be disposed of according to AVV-ASN: 080409* (adhesive and sealing compound residues containing organic solvents or other hazardous substances).

The above information replaces all previous technical information about the product. Thus, this information is no longer valid. The details have been compiled according to the latest state of application technology. Please observe, however, that, depending on the state of the construction object, deviations from the method of application suggested in the datasheet may be required. Unless agreed otherwise in individual contracts, any information contained in the datasheet shall be non-binding and thus does not represent an agreed product constitution. We reserve the right to any changes in the information contained in this datasheet anytime.
BORNIT<sup class=® Corrosion Preventer, application image">

UFI AXC0-H0Q8-F005-SV80

Safety Data Sheet Poison Information Centre , 24h: +49-361-730730

ERFURT - Poison Control Centre Erfurt, Joint Poison Information Centre of the federal States of Mecklenburg-Western Pomerania, Saxony, Saxony-Anhalt and Thuringia; ggiz@ggiz-erfurt.de; www.ggiz-erfurt.de

-     What: name of the substance or product as precisely as possible, etc.
-     How much: as exact a quantity as possible
-     Who: Age, weight, sex and condition of the person(s) concerned.
-     When: Time of the event
-     Where: Place of occurrence
-     How: ingestion, inhalation, skin contact, etc.
-     Why: accidentally or intentionally


UN 1993

Hazard pictograms

signal word

Hazard-determining components for labelling
Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclics, <2% aromatics; Hydrocarbons, C9, aromatics

H226: Flammable liquid and vapour.
H336: May cause drowsiness or dizziness.
H412: Harmful to aquatic life with long lasting effects.

EUH066: Repeated exposure may cause skin dryness or cracking.

P102: Keep out of reach of children.
P261: Avoid breathing dust/fume/gas/mist/vapours/spray.
P271: Use only outdoors or in a well-ventilated area.
P301 + P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor.
P331: Do NOT induce vomiting.
P403 + P233: Store in a well-ventilated place. Keep container tightly closed.

recommended, personal protective equipment: