BORNIT® Edge Module
road construction | edge sealing | load-bearing | binder | surface layer
Short information
- add-on module for the BORNIT® Flexomat 3.1
- for quick and clean application of BORNIT® Edge Flex to the outer asphalt flank of the load-bearing, binder and surface layer
Consumption
Storage note
store dry, protect from moisture; frost-free when filled!
Complementary products
CleaningFollow-up products
Clean tools with water immediately after use
status technical data sheet
27th September 2021
Areas of application
BORNIT® Edge Module is an add-on module for machine sealing (with BORNIT® Flexomat 3.1) of the higher edge of the road of traffic areas made of asphalt against laterally penetrating surface water.
Type and properties
Add-on module for the BORNIT® Flexomat 3.1; used to seal the edges of load-bearing, binder and surface layers with BORNIT® Edge Flex.
Processing
The edge module is screwed to the module plate at the front of the BORNIT® Flexomat 3.1 with screws.
The hose for material transport is connected by means of a union nut to the thread provided on the material discharge pipe of the Flexomat (right side in the centre of the pressure vessel).
The outrigger can be adjusted to the shape of the edge to be sealed, depending on the conditions on the construction site.
The hose for material transport is connected by means of a union nut to the thread provided on the material discharge pipe of the Flexomat (right side in the centre of the pressure vessel).
The outrigger can be adjusted to the shape of the edge to be sealed, depending on the conditions on the construction site.
Product data in brief
Product type
add-on module for the BORNIT® Flexomat 3.1
Base
metal outrigger
colour(s)
red-black
Cleaning
BORNIT® MultiClean Spray, BORNIT® MultiClean, BORNIT® Bitumen Cleaner
storage
store dry, protect from moisture; frost-free when filled!
Hazard class according to ADR
keine
Health and fire protection, occupational safety
To ensure safe handling of the product, the physical, safety, toxicological and ecological information provided online, the information in the current operating instructions and the additional information on the label must be read and followed before purchasing or using the product! The applicable regulations, ordinances and laws must be complied with.
In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.
In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.
Storage
The module must be stored in a dry place.
Note
The information set out above supersedes all previous technical information relating to the product. The previous information is therefore no longer valid. The details have been compiled in accordance with the latest state of the art in application technology. Please note, however, that depending on the condition of the building, it may be necessary to deviate from the working method recommended in this data sheet. Unless otherwise agreed in an individual contract, all information contained in this data sheet is non-binding and therefore does not constitute an agreed product specification. We reserve the right to make changes to the information contained in this data sheet at any time.
The product illustrations are to be understood as examples. No legally binding claim can be derived from them. We reserve the right to make changes to the product’s appearance.
Our packaging complies with the relevant legal requirements and with Regulation (EU) 2025/40 on packaging and packaging waste (PPWR). The technical documentation in accordance with Annex VII is available and can be provided on request by email to info@bornit.de.
The product illustrations are to be understood as examples. No legally binding claim can be derived from them. We reserve the right to make changes to the product’s appearance.
Our packaging complies with the relevant legal requirements and with Regulation (EU) 2025/40 on packaging and packaging waste (PPWR). The technical documentation in accordance with Annex VII is available and can be provided on request by email to info@bornit.de.
