BORNIT^® Profi 1C S

status technical data sheet

24 November 2021

areas of application

BORNIT^® Profi 1C S is used for permanent, flexible external waterproofing of building structures in the area in contact with the ground and is applied with spraying equipment. The product is suitable for application on horizontal and vertical surfaces. To select the appropriate spraying technique, please contact our application engineers. BORNIT^® Profi 1C S can also be used for intermediate waterproofing (under screed) of floor slabs, balconies and terraces to bituminous and mineral substrates in the area in contact with the ground. BORNIT^® Profi 1C S adheres well to all dry and slightly moist mineral substrates as well as bituminous substrates with sufficient stability (e.g., old cold and hot coatings or thick coatings).

type and properties

BORNIT^® Profi 1C S is a modified, single-component, polystyrene-filled and polymer-modified thick bitumen coating (PMBC) for rational application with suitable spraying machines. BORNIT^® Profi 1C S is supplied in large containers, the BORNIT^®-BituBox, and applied by spraying (operating radius of approx. 75 m possible).
The product is characterised by particularly fast rain-resistance and thorough drying. With its high proportion of solids, a high dry layer thickness (more than 90 % of the wet layer thickness) is achieved, with economical material usage.
BORNIT^® Profi 1C S is solvent-free and environmentally friendly. Due to the BORNIT^®-BituBox as bulk packaging, packaging waste is reduced to a minimum compared to a similar quantity of product in buckets.
After thorough drying, a highly flexible, crack-bridging and watertight foundation waterproofing is achieved, which is resistant to any aggressive substances naturally occurring in the soil.
Optionally, BORNIT^®-Profidicht 1K S can be sprayed with reaction accelerator BORNIT^®-SpeedUp. In this way, rain resistance can be achieved after a few minutes.

advantages

surface

Step 1: The substrate must be free from ridges or shard-edged unevennesses as well as soil.
Step 2: Unfilled or badly filled depressions, such as masonry joints, mortar pockets or surface defects larger than 5 mm must be repaired with suitable mortar. No plaster layer is required for fully and flushly grouted masonry. Voids smaller than 5 mm as well as pores in the substrate can be closed by applying the thick bitumen coating in a scraping manner. Especially for concrete surfaces, application in a scraping manner is likewise recommended in order to avoid the formation of bubbles.
Step 3: It must be observed that the substrate is firm, clean, free from dust and free from separating substances. The substrate should be dry and absorbent. The surface temperature must be at least 3 Kelvin above the dew point temperature of the ambient air.
Step 4: A priming layer of BORNIT^® Basement Primer or BORNIT^® Unibit (diluted with water 1:2) must be applied to the substrate. For solidification of sanding substrates, priming with BORNIT^® Solidificator SB3 (diluted with clean tap water at a mixing ratio of 1:1) is recommended. When applying the thick bitumen coating in a scraping manner, the primer must be applied in advance. A scratch coat does not replace the primer. After drying of the primer, the substrate is prepared for the application of the scratch coat or the thick coating, resp.
Important: During the construction phase, thick bitumen coatings can be damaged by water affecting their rear side. In principle, it must be ensured that the coating is not damaged by water affecting the adhesive side. If necessary, water-impermeable intermediate layers of mineral sealing slurry (e.g., BORNIT^® Slurry SF) must be applied, which cannot be detached from the substrate by water pressure.

processing

Upon processing BORNIT^® Profi 1C S, in principle, the current DIN 18533 must be observed. The processing of PMBC depends on the respective water impact class at the building object. Therefore, it must be observed that the water impact class present is clearly specified by the planner prior to the start of any work.
BORNIT^® Profi 1C S is delivered ready for use and applied to the substrate prepared as stated above using suitable spraying equipment (e.g. GRACO GH 5040). BORNIT^® Profi 1C S must not be applied in case of frost or impending rain. Processing should be undertaken at object and ambient temperatures not below +5 °C and not above +30 °C.

When processing with BORNIT^®-SpeedUp, a special 2C spray gun and a second spraying device (e.g. Graco GMAX II 3900) are mandatory. Optimum mixing of the two components is achieved by 2 separate spraying nozzles. The mixing ratio should not exceed 5 % BORNIT^® SpeedUp to BORNIT^® Profi 1C S. More detailed information is available at a special seminar for waterproofing applied by spraying devices in our company.

Application of the thick coating is undertaken according to the current DIN 18533 in two layers. Upon waterproofing against ground moisture and non-pressing water (DIN 18533 W1-E) and splash and capillary water (DIN 18533 W4-E), the layers can be applied fresh on fresh.
Upon waterproofing against moderately pressing water (DIN 18533 W2.1-E) and non-pressing water on ceilings covered with earth (DIN 18533 W3-E), the first waterproofing layer must have dried off to such extent prior to application of the second layer, that it is not damaged by the application. A reinforcing insert (BORNIT^® Glass Fabric 165) must be embedded into the first waterproofing layer over its entire surface.

According to the current DIN 18533 standard, hollow fillets must be formed using a mineral material (BORNIT^® Sealing Mortar) as an approx. bottle diameter-sized hollow fillet or with a two-component thick coating (BORNIT^® Repabit, quick-drying) prior to the surface sealing. As a deviating, yet innovative and secure problem solution, here we recommend the use of BORNIT^® Triangle Tape (bitumen profile, fusible) as an alternative. Special attention must be paid to proper execution of the waterproofing in the area of joints, connections and terminations as well as penetrations.
 
The fresh coating must be protected from rain and solar irradiation!

The waterproofing layer must be protected against damages. Protective and drainage layers, however, must only be applied after complete and thorough drying of the waterproofing layer (depending on weather and substrate, 2 to several days). For bonding insulation boards, BORNIT^® Profi 1C Express can be used for manual and BORNIT^® Profi 1C S for machine application.
Suitable protective layers are, e.g., dimpled plastic sheeting with sliding film and filter fleece as well as thermally or bituminously bound seepage panels. Subsequently, the construction pit can be filled. In that, DIN 18533-1, Point 14 must be observed.

consumption

• for the water impact classes ground moisture / non-pressing water (DIN 18533 W1-E) as well as splash and capillary water (DIN 18533 W4-E):
approx. 3.5 – 4.0 l/m² = wet layer thickness 3.5 mm = dry layer thickness 3.0 mm

• for the water impact classes moderately pressing water (DIN 18533 W2.1-E) and non-pressing water on ceilings covered with earth (DIN 18533 W3-E):
approx. 4.5 – 5.0 l/m² = wet layer thickness 4.5 mm = dry layer thickness 4.0 mm

• adhesion of insulation panels:
approx. 2 l/m² with punctiform adhesion
approx. 3 l/m² with adhesion over the entire surface

The consumption figures stated are values based on practical experience.
The layer thickness allowance according to DIN 18533-3 must be observed.

layer thickness control

According to the current DIN 18533 W1-E and W4-E, a layer thickness test in the fresh state (wet layer thickness) at the execution object as well as an inspection of the thorough drying state at a reference sample located in the construction pit (e.g., a brick) must be performed. For waterproofing according to DIN 18533 W2.1-E and W3-E, the results of these tests must be documented. Water impact class according to DIN 18533 W1-E and W4-E Minimum dry layer thickness: 3 mm Water impact class according to DIN 18533 W2.1-E and W3-E Minimum dry layer thickness: 4 mm

product type

single-component thick bitumen coating (PMBC)

base

polymer-modified bitumen emulsion with special fillers

solvent

none

density at +20 °C

approx. 0.80-0.85 g/cm³

PH-value

11.0 - 11.5

consistency

paste-like, suitable for trowel application

colour(s)

black

application

smoothing trowel, spraying equipment

processing temperature (ambient and substrate)

not below +5 °C and not above +30 °C

thorough hardening time

2 to several days, depending on air humidity, temperature, layer thickness and substrate

cleaning

in the fresh state with water, in the hardened state with BORNIT^® MultiClean Spray, BORNIT^® MultiClean or BORNIT^® Bitumen Cleaner

storage

store not below +5 °C, absolutely frost-free!

shelf life

in originally sealed container storable for 6 months

GISCODE

BBP10

GISCODE link comp. A

https://www.wingisonline.de/showbetrandoc.aspx?gisbaunr=4/00000018210/000009&docid=1995&lang=de

VOC category

actual permissible VOC content

0 g/ltr.

substances hazardous to health in terms of the ordinance on hazardous materials

none

hazard class according to ADR

none

boiling start and Boiling range

+100 °C

Water impermeability

impermeable at 0.75 bar over 72 hours

Water vapour diffusion factor µ

approx. 8000 (according to DIN EN 12086)

SD value (m)

26.3

health and fire protection, occupational safety

For information on handling, safety and ecology, please refer to the current safety datasheet.

storage

In originally sealed containers storable for 6 months. BORNIT^® Profi 1C Express must be protected from frost! Thermal impact above +30 °C and direct solar irradiation must be avoided.

disposal note

Only recycle completely empty containers. Material residues can be disposed of according to AVV-ASN: 080410 (waste adhesives and sealing compounds except for those falling under 080409).

note

The above information replaces all previous technical information about the product. Thus, this information is no longer valid. The details have been compiled according to the latest state of application technology. Please observe, however, that, depending on the state of the construction object, deviations from the method of application suggested in the datasheet may be required. Unless agreed otherwise in individual contracts, any information contained in the datasheet shall be non-binding and thus does not represent an agreed product constitution. We reserve the right to any changes in the information contained in this datasheet anytime.