220

BORNIT® Bitumen Mastic

bitumen | bitumen sealant | defects in roofing membranes | filler compound
BORNIT
Short information
  • solvent-based, fibre-reinforced bituminous sealing compound
  • for repair of defects in roofing membranes of bituminous roof sheetings
  • for sealing coving joints along chimneys and wall transitions
  • UV-resistant, crack-bridging, can be applied by trowel
Product
Colour
Content
Bitumen Mastic
black
1 kg / can
sufficient for:
Order-No.
EAN code
box
approx. 0.8 m²
6800000347
4 017228 00379 5
18 can
Bitumen Mastic
black
2,5 kg / bucket
sufficient for:
Order-No.
EAN code
euro pallet
approx. 2 m²
6800000340
4 017228 00364 1
99 bucket
Bitumen Mastic
black
6 kg / bucket
sufficient for:
Order-No.
EAN code
euro pallet
approx. 5 m²
6800000339
4 017228 003658
75 bucket
Bitumen Mastic
black
12 kg / bucket
sufficient for:
Order-No.
EAN code
euro pallet
approx. 10 m²
6800000338
4 017228 003665
45 bucket
Consumption
approx. 1.2 kg/m² per mm of layer thickness
Storage note
  • not sensitive to frost
  • in originally sealed containers storable for 12 months
  • keep away from ignition sources!

Status technical data sheet
09 November 2020

Areas of application
BORNIT® Bitumen Mastic is used for repair and waterproofing of defects in roofing membranes of bituminous roof sheeting as well as junctions and edges of penetrations, installed components, etc. The product adheres well to mineral substrates (concrete, plaster, masonry), bituminous roof sheeting and coatings as well as fibre-cement surfaces. Application on non-absorbent substrates, like non-ferrous metals and steel, should only be undertaken after priming and with a maximum pitch of 25° (approx. 50 %) and maximum layer thicknesses of 4 mm in order to avoid running off.
Not suitable for plastic sheeting, polystyrene or rigid foam substrates as well as impregnated surfaces, e.g. treated with silicone-containing coatings.
Prior to application on concrete, masonry and plaster, the substrate must be primed with BORNIT® Bitumen Primer for dust binding.

Type and properties
BORNIT® Bitumen Mastic is a paste-like, fibre-reinforced bituminous sealing compound for cold application. The solvent-containing product is resistant to non-oxidising acids and contains stabilising additives to prevent settling. The material properties only become fully effective following complete and thorough drying. Then, the filling compound is water-impermeable and resistant to adverse weather conditions. It is not resistant to solvents, fuels, oils and oxidising acids. BORNIT® Bitumen Mastic is free from tar, asbestos, PCK and PCB. Tested according to AIB DS 835.

Advantages
  • manufactured ready for processing
  • crack-bridging, waterproof and UV-resistant
  • universally applicable
  • low equipment and material costs and effort during processing

Surface
The substrate must be dry, clean, oil- and grease-free as well as stable. For better adhesion on concrete, masonry or plaster, BORNIT® Bitumen Primer is recommended for priming.
The primer must be completely dry before applying the filling compound.
The product contains solvents, which may damage synthetic materials, etc. Check compatibility with the substrate prior to application!

Processing
BORNIT® Bitumen Mastic is manufactured ready for processing and is applied directly as delivered with a trowel or spatula. In case of cold weather, store the filling compound in a heated room prior to processing.
BORNIT® Bitumen Mastic is best processable at temperatures between +5 °C and +35 °C. With previous warm storage, processing, however, is possible down to an outside temperature of -5 °C.
Intensively spread the product onto the substrate, tapering out at the edges.
In that, application thicknesses of up to 5 mm are possible. Only apply thicker compound layers in several work steps with a time interval inbetween, enabling secure and uniform evaporation of the solvent! Otherwise, blistering due to solar irradiation and very long (several weeks) drying times cannot be excluded. Do not apply to heated or easily heatable substrates.
During drying, protect the coating from moisture, rain or condensation water.

Consumption
approx. 1.2 kg/m² per mm of layer thickness

Product data in brief
Product type
bituminous filling compound
Base
bitumen, solvent, aggregates
Solvent
white spirit
Density at +20 °C
approx. 1.20 - 1.30 g/cm³
Softening point acc. to cone/ring
+160 °C (from the solid EP)
Consistency
paste-like
Heat resistance
at +70 °C, 2 h, no running off
Colour(s)
black
Application
with a spatula
Cleaning
BORNIT® MultiClean Spray, BORNIT® MultiClean or BORNIT® Bitumen Cleaner
Storage
not sensitive to frost
Shelf life
in originally sealed containers storable for 12 months keep away from ignition sources!
GISCODE
BBP20
VOC category
2004/42/EG g/Lb: 350 g/ltr.
Actual permissible VOC content
< 230 g/l
Hazard class according to ADR
entzündbare Flüssigkeiten (Flam. Liq. 3)
Acc. to Industrial Safety Regulation (BetrSichV)
flammable
Flash point
+24 °C

Water permeability 0.5 bar, 8 h
impermeable
Max. roof pitch
25°

Health and fire protection, occupational safety
For information on handling, safety and ecology, please refer to the current safety datasheet.

Storage
The product can be stored for 12 months in the original sealed container. Not sensitive to frost!

Disposal note
Only recycle completely empty containers. Material residues can be disposed of according to AVV-ASN: 080409* (adhesive and sealing compound residues containing organic solvents or other hazardous substances).

Note
The above information replaces all previous technical information about the product. Thus, this information is no longer valid. The details have been compiled according to the latest state of application technology. Please observe, however, that, depending on the state of the construction object, deviations from the method of application suggested in the datasheet may be required. Unless agreed otherwise in individual contracts, any information contained in the datasheet shall be non-binding and thus does not represent an agreed product constitution. We reserve the right to any changes in the information contained in this datasheet anytime.

UFI P300-P0FG-500V-GRU3

Safety Data Sheet Poison Information Centre , 24h: +49-361-730730

ERFURT - Poison Control Centre Erfurt, Joint Poison Information Centre of the federal States of Mecklenburg-Western Pomerania, Saxony, Saxony-Anhalt and Thuringia; ggiz@ggiz-erfurt.de; www.ggiz-erfurt.de

-     What: name of the substance or product as precisely as possible, etc.
-     How much: as exact a quantity as possible
-     Who: Age, weight, sex and condition of the person(s) concerned.
-     When: Time of the event
-     Where: Place of occurrence
-     How: ingestion, inhalation, skin contact, etc.
-     Why: accidentally or intentionally

recommended, personal protective equipment: