BORNIT® Cold Joint Sealant
joint filler | joint | joint sealing | weather resistance

- two-component, polysulphide-based joint sealant
- for sealing vertical or inclined joints in concrete traffic areas and cut asphalt surfaces
- permanently elastic
- stable
euro pallet
30 box
euro pallet
18 box
euro pallet
30 box
euro pallet
18 box
- dry, cool (below +25 °C)
- in originally sealed containers storable for 12 months
BORNIT® Cold Joint Sealant is suitable for sealing floor or ground-level joints between concrete elements as well as concrete components and asphalt surfaces subject mechanical stresses (vehicle and pedestrian traffic), chemical stresses from de-icing salts and temperature-dependent movements of the components. Upon use in concrete surfaces, BORNIT® Cold Joint Sealant can also be subjected to chemical stresses from fuels.
Horizontal joints with an inclination of less than 3 % should be sealed with the self-levelling BORNIT® Cold Sealing Compound. The joint sealant must not be used for joints, which are permanently under the surface of liquids (e.g. in swimming pools, clarification tanks) or are exposed to strongly oxidising acids and bases, as well as for joints in facilities for storing, filling and transhipping of water pollutants (called LAU plants) and for glass sealing.
- very flexible
- waterproof and UV-resistant
- universally applicable
- less equipment, material and labor required for processing
Subsequently, for concrete joints, thoroughly mixed BORNIT® Concrete Primer must be uniformly applied to the dry fusion faces. After a flash-off time of 0.5-2 hours (depending on the temperature, the primer should not be completely dry), BORNIT® Cold Joint Sealant can be inserted. The BORNIT® Concrete Primer should not be completely dried off. If more than 24 hours should have passed, the primer layer must be roughened and new primer applied.
Asphalt joints must be primed with BORNIT® Asphalt Primer. The asphalt joints must be freshly cut, since adhesion problems would otherwise result. The components A and B are mixed thoroughly and the primer is uniformly applied with a brush. After a flash-off time of 2 to 6 hours (component temperature > +25 °C approx. 2 hours, < +10 °C approx. 6 hours), the sealant can be introduced. The asphalt primer should have dried as far as possible. It must be observed that no moisture film has formed on the primer surface due to undercutting of the dew point. For BORNIT® Cold Joint Sealant, the components A and B are both contained in one container in layers and not packaged separately. First mix the components (layers) with a suitable tool (slow-speed drill with mixing paddle stirrer), until there are no colour streaks anymore. Now insert the joint sealant into the joint with suitable tools (e.g. manual or compressed air guns) and smooth it with a spatula, smoothing stick or the like within the processing time. Prior to mixing, the temperature of the sealant should be min. +10 °C. The component temperature must not be below +5 °C and not above +40 °C. Until reaching the full load-bearing capacity, a thorough hardening time of min. 48 hours at +20 °C ground and materials temperature must be complied with.
Product data in brief
In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.
BORNIT-Werk Aschenborn GmbH
Reichenbacher Straße 117
08056 Zwickau / Germany
2009
1381-1445/2025
DIN EN 14188-2:2004
System: Two-component (M) / Type: stable (ns)
Cold workable, spatula-applicable polysulphide-based joint sealant
Adhesive capacity and expansibility | Tensile modulus at 100 % expansion: at +23°C ≥ 0.15 MPa, at -20°C ≤ 0.6 MPa |
Adhesive capacity | No failure at -20°C ≤ 0.6 MPa |
Water impermeability | Resilience ≥ 70%, Volume loss ≤ 5% |
Resistance to deformation | Resilience ≥ 70 %, Loss in volume ≤ 5 % |
Durability of water impermeability when exposed to chemicals | Passed |
Durability of all mandated properties against ageing | Change in the tensile modulus at 100 % expansion: ± ≤ 20 % |
Flame resistance | Passed |
Component A
P103: Read carefully and follow all instructions.
P273: Avoid release to the environment.
P501: Dispose of contents/container to a suitable recycling or disposal facility.
Component B
EUH211: Warning! Hazardous respirable droplets may be formed when sprayed. Do not breathe spray or mist.
P273: Avoid release to the environment.
P501: Dispose of contents/container to a suitable recycling or disposal facility.
P103: Read carefully and follow all instructions.