187

BORNIT® Flexomat 3.1

road | centre seam | edge sealing | crack repair | layer bonding
BORNIT
Short information
  • one core unit for 4 different applications
  • easy to operate and low maintenance effort
Product
Colour
Content
Flexomat 3.1
red
1 piece / Stück
sufficient for:
Order-No.
EAN code
one way pallet
6800000508
4 017228 00090 9
1 Stück
Consumption
Storage note
  • store dry,
  • when filled with solvent-free product absolutely frost-free!

Status technical data sheet
30 November 2020

Areas of application
1. BORNIT® Flexomat 3.1 + Joint Module + BORNIT® Joint Flex can be used to produce flexible and durable seams during the strip-by-strip construction of rolled asphalt surfaces.

2. BORNIT® Flexomat 3.1 + Edge Module + BORNIT® Joint Flex can be used to produce flexible and durable seams during the strip-by-strip construction of rolled asphalt in the load-bearing and binder courses.

3. BORNIT® Flexomat 3.1 + Edge Module + BORNIT® Edge Flex reliably protects the higher edge area of asphalt surfaces from water penetration in one operation (load-bearing, binder and surface course).

4. BORNIT® Flexomat 3.1 + Crack Module SpeedUp + BORNIT® Crack Flex + BORNIT® SpeedUp can be used to seal cracks safely and flexibly in the cold process.

Type and properties
The BORNIT® Flexomat 3.1 is used to process cold liquid, sprayable and solvent-free bitumen emulsions. A 56.9 litre compressed air tank serves as the supply container, which is filled with the corresponding BORNIT® material. Compressed air is supplied at max. 4 bar, which is generated by a compressor, which is driven by a 4-stroke Honda petrol engine. The BORNIT® Flexomat 3.1 is available as a basic unit. By attaching the 3 different modules (Joint Module, Crack Module, Edge Module), 4 different areas of application can be handled with one device.

Joint Module:

- centre seam treatment of the surface layer during the strip-by-strip construction of rolled asphalt surfaces

Edge Module:

- seam treatment of the load-bearing and binder course during the strip-by-strip construction of rolled asphalt surfaces
- sealing of higher edge (load-bearing, binder and surface course) in asphalt surfaces

Crack Module:

- fast and secure rehabilitation and closure of cracks in asphalt

Advantages
  • one core unit for 4 different applications
  • easy to operate and low maintenance effort

Processing
Operation at a glance
In principle, the unit may only be used in compliance with all legal regulations and with the products BORNIT® Crack Flex, Edge Flex, Joint Flex and the corresponding add-on modules to be used as intended. (Observe operating instructions!). The material is filled into the pressure vessel from the delivery container. Before opening the lid of the vessel, make sure that it is vented (depressurised). Then close the pressure vessel tightly and start the engine. The necessary working pressure is built up in the vessel within approx. 2 minutes. The working pressure depends on the material to be processed.

BORNIT® Joint Flex 1 bar

BORNIT® Crack Flex 4 bar

BORNIT® Edge Flex 2 bar

The pressure is set constantly by the controlled opening and closing of the ball valve on the lid of the container. By opening the hand valve, the material is conveyed through the pressure hoses to the attached module and on to the area to be coated.

The required amount of material is controlled by the feed rate of the BORNIT® Flexomat 3.1 and by the applied pressure.

Product data in brief
Colour(s)
red
Dimensions
Dimension (LxWxH) approx. 1100 mm x 580 mm x 1300 mm
Cleaning
If work is expected to be interrupted for more than 2 weeks, the unit must be emptied and rinsed immediately with water. Already dried material residues can be removed with BORNIT® MultiClean Spray or BORNIT® MultiClean.
Storage
store dry, when filled with solvent-free product absolutely frost-free!

Dimension (LxWxH)
approx. 1100 mm x 580 mm x 1300 mm
Weight (unfilled)
approx. 105 kg
Nominal capacity pressure vessel
56,9 liter
Operating pressure
max. 4 bar
Engine
4-stroke petrol engine
Engine type and power
Honda GX 100, 2.1 KW

Health and fire protection, occupational safety
The BORNIT® Flexomat 3.1 may only be used for its intended purpose, i.e. using the material intended for it (observe the technical data sheets!). The device is designed for ongoing road maintenance and may only be used, maintained and repaired by persons over the age of 18 who are knowledgeable about the operating instructions and have the appropriate specialist training. The guidelines can be obtained from: Tiefbau-BG under order no. ZH 1/536.
For information on handling, safety and ecology, please refer to the current safety data sheet.

Storage
If work is expected to be interrupted for more than 2 weeks, the unit must be emptied and rinsed immediately with water. Already dried material residues can be removed with BORNIT® MultiClean. Otherwise, the unit must be stored in a dry and frost-free place.

Note
The above information replaces all previous technical information about the product. Thus, this information is no longer valid. The details have been compiled according to the latest state of application technology. Please observe, however, that, depending on the state of the construction object, deviations from the method of application suggested in the datasheet may be required. Unless agreed otherwise in individual contracts, any information contained in the datasheet shall be non-binding and thus does not represent an agreed product constitution. We reserve the right to any changes in the information contained in this datasheet anytime.
BORNIT<sup class=® Flexomat 3.1">
BORNIT<sup class=® Flexomat 3.1, seam, centre seam, road construction, layer bonding">
recommended, personal protective equipment: