BORNIT® Solidificator (SM3)
system module | basement and interior waterproofing | surface | foundation
Short information
- water-thin reaction liquid
- for solidification of the substrate
- reacts to a water-insoluble compound
- brushable
Consumption
approx. 0.5 kg/m² depending on the substrate
Storage note
- store dry, cool but frost-free!
- in originally sealed containers storable for 12 months
Complementary products
status technical data sheet
12th January 2021
Areas of application
BORNIT® Solidificator (SM3) is mainly used for silicification or solidification, resp., of porous or sanding mineral construction materials, and thus to avoid spalling, as well as for increasing surface strength and resistance to abrasion. BORNIT® Solidificator (SM3) can also be used as a substrate-solidifying primer, e.g., underneath PMBC and BORNIT® Profi Hybrid 2K (with clean tap water at a mixing ratio of 1:1). The product is also used as component 3 of the BORNIT® Basement Coating System upon inside waterproofing of moist basements.
Type and properties
BORNIT® Solidificator (SM3) is a deep-penetrating silicification preparation with a hydrophobic and substrate-solidifying effect. BORNIT® Solidificator (SM3) is solvent-free and therefore not environmentally harmful. The active agents penetrate deep into the substrate and react into water-insoluble compounds. Thus, the pores are clogged and permanently waterproofed with constantly progressing mineralisation.
Advantages
- easiest handling
- very good penetration
Surface
The substrate must be clean, firm and free from separating substances (oils, greases, old coatings). It should be dry or only slightly moist.
Processing
As component 3 of the BORNIT® Basement Coating System, BORNIT® Solidificator (SM3) is applied undiluted in one working step using a roller or brush.
As a substrate-solidifying primer, e.g., underneath PMBC, the solidificator has to be used diluted (with clean tap water at a mixing ratio of 1:1). For porous concrete, two-time application is required. Application of subsequent layers, e.g., PMBC, is possible after approx. 24 hours of thorough drying. Upon processing within the BORNIT® Basement Coating System, observe the respective product datasheet.
The product is alkaline. Therefore, clinker bricks or other sensitive surfaces (e.g., glass) must be effectively covered prior to application.
Application is possible at temperatures above +5 °C.
As a substrate-solidifying primer, e.g., underneath PMBC, the solidificator has to be used diluted (with clean tap water at a mixing ratio of 1:1). For porous concrete, two-time application is required. Application of subsequent layers, e.g., PMBC, is possible after approx. 24 hours of thorough drying. Upon processing within the BORNIT® Basement Coating System, observe the respective product datasheet.
The product is alkaline. Therefore, clinker bricks or other sensitive surfaces (e.g., glass) must be effectively covered prior to application.
Application is possible at temperatures above +5 °C.
Consumption
approx. 0.5 kg/m² depending on the substrate
Product data in brief
Density at +20 °C
approx. 1.2 g/cm³
PH-value
10.0
Consistency
thin liquid
colour(s)
transparent
Application
brush, paintbrush, roller, sprayer
Processing temperature (ambient and substrate)
at least +5°C
storage
store dry, cool but frost-free!
Shelf life
in originally sealed containers storable for 12 months
Hazard class according to ADR
keine
Health and fire protection, occupational safety
To ensure safe handling of the product, the physical, safety, toxicological and ecological information provided online, the information in the current safety data sheet and the additional information on the label must be read and followed before purchasing or using the product! The applicable regulations, ordinances and laws must be complied with.
In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.
In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.
Storage
In originally sealed containers storable for 12 months.
Disposal note
Only recycle completely empty containers. Material residues can be disposed of according to AVV-ASN: 060299 (wastes not otherwise specified).
Note
The information set out above supersedes all previous technical information relating to the product. The previous information is therefore no longer valid. The details have been compiled in accordance with the latest state of the art in application technology. Please note, however, that depending on the condition of the building, it may be necessary to deviate from the working method recommended in this data sheet. Unless otherwise agreed in an individual contract, all information contained in this data sheet is non-binding and therefore does not constitute an agreed product specification. We reserve the right to make changes to the information contained in this data sheet at any time.
The product illustrations are to be understood as examples. No legally binding claim can be derived from them. We reserve the right to make changes to the product’s appearance.
Our packaging complies with the relevant legal requirements and with Regulation (EU) 2025/40 on packaging and packaging waste (PPWR). The technical documentation in accordance with Annex VII is available and can be provided on request by email to info@bornit.de.
The product illustrations are to be understood as examples. No legally binding claim can be derived from them. We reserve the right to make changes to the product’s appearance.
Our packaging complies with the relevant legal requirements and with Regulation (EU) 2025/40 on packaging and packaging waste (PPWR). The technical documentation in accordance with Annex VII is available and can be provided on request by email to info@bornit.de.
® Solidificator (SM3), processing, application image">
® Solidificator (SM3), processing, application image">Recommended, personal protective equipment:
