BORNIT® WL Bitumen Mastic (white label) (no longer in the product range)

bitumen | surface sealing | top sealing | crack-bridging
short information
  • manufactured ready for processing
  • crack-bridging, waterproof and UV-resistant
  • universally applicable
  • low equipment and material costs and effort during processing
Bitumen Mastic (white label)
5 kg / bucket
sufficient for:
EAN code
euro pallet
approx. 4.2 m² per mm layer thickness
4 017228 00391 7
75 bucket
Bitumen Mastic (white label)
10 kg / bucket
sufficient for:
EAN code
euro pallet
approx. 8.3 m² per mm layer thickness
4 017228 00393 1
45 bucket
Bitumen Mastic (white label)
25 kg / bucket
sufficient for:
EAN code
euro pallet
approx. 20.8 m² per mm layer thickness
4 017228 00625 3
18 bucket
approx. 1.2 kg/m² per mm of layer thickness
storage note
  • not sensitive to frost,
  • keep away from ignition sources!
  • in originally sealed containers storable for 12 months

status technical data sheet
02 June 2021

areas of application
BORNIT® Bitumen Mastic is used for repair and waterproofing of defects in roofing membranes of bituminous roof sheeting as well as junctions and edges of penetrations, installed components, etc. The product adheres well to mineral substrates (concrete, plaster, masonry), bituminous roof sheeting and coatings as well as fibre-cement surfaces. Application on non-absorbent substrates, like non-ferrous metals and steel, should only be undertaken after priming and with a maximum pitch of 25° (approx. 50 %) and maximum layer thicknesses of 4 mm in order to avoid running off.
Not suitable for plastic sheeting, polystyrene or rigid foam substrates as well as impregnated surfaces, e.g. treated with silicone-containing coatings.
Prior to application on concrete, masonry and plaster, the substrate must be primed with BORNIT® Bitumen Primer for dust binding.

type and properties
BORNIT® Bitumen Mastic is a paste-like, fibre-reinforced bituminous sealing compound for cold application. The solvent-containing product is resistant to non-oxidising acids and contains stabilising additives to prevent settling. The material properties only become fully effective following complete and thorough drying. Then, the filling compound is water-impermeable and resistant to adverse weather conditions. It is not resistant to solvents, fuels, oils and oxidising acids. BORNIT® Bitumen Mastic is free from tar, asbestos, PCK and PCB. Tested according to AIB DS 835.

  • manufactured ready for processing
  • crack-bridging, waterproof and UV-resistant
  • universally applicable
  • low equipment and material costs and effort during processing

The substrate must be dry, clean, oil- and grease-free as well as stable. For better adhesion on concrete, masonry or plaster, BORNIT® Bitumen Primer is recommended for priming.
The primer must be completely dry before applying the filling compound.
The product contains solvents, which may damage synthetic materials, etc. Check compatibility with the substrate prior to application!

BORNIT® Bitumen Mastic is manufactured ready for processing and is applied directly as delivered with a trowel or spatula. In case of cold weather, store the filling compound in a heated room prior to processing.
BORNIT® Bitumen Mastic is best processable at temperatures between +5 °C and +35 °C. With previous warm storage, processing, however, is possible down to an outside temperature of -5 °C.
Intensively spread the product onto the substrate, tapering out at the edges.
In that, application thicknesses of up to 5 mm are possible. Only apply thicker compound layers in several work steps with a time interval inbetween, enabling secure and uniform evaporation of the solvent! Otherwise, blistering due to solar irradiation and very long (several weeks) drying times cannot be excluded. Do not apply to heated or easily heatable substrates.
During drying, protect the coating from moisture, rain or condensation water.

approx. 1.2 kg/m² per mm of layer thickness

product data in brief
product type
bituminous filling compound
bitumen, solvent, aggregates
white spirit
density at +20 °C
approx. 1.20 - 1.30 g/cm³
softening point acc. to cone/ring
+160 °C (from the solid EP)
heat resistance
at +70 °C, 2 h, no running off
with a spatula
BORNIT®-MultiClean Fix, BORNIT®-MultiClean oder BORNIT®-Bitumenreiniger
not sensitive to frost, keep away from ignition sources!
shelf life
in originally sealed containers storable for 12 months
GISCODE link comp. A
VOC category
actual permissible VOC content
< 230 g/ltr.
hazard class according to ADR
entzündbare Flüssigkeiten (Flam. Liq. 3)
Acc. to Industrial Safety Regulation (BetrSichV)
boiling start and Boiling range
> +150 °C
upper/lower explosion limit
6,4 - 0,67 Vol-%
flash point
24,0 °C
Water permeability 0.5 bar, 8 h
Max. roof inclination

health and fire protection, occupational safety
Caution - Only use in well-ventilated outdoor areas. Not suitable for use in closed rooms or poorly ventilated pits!
Do not eat, drink or smoke while working, keep away from sources of ignition.

To ensure safe handling of the product, the physical, safety, toxicological and ecological information provided online, the information in the current safety data sheet and the additional information on the label must be read and followed before purchasing or using the product! The applicable regulations, ordinances and laws must be complied with.

In case of doubt, please contact the BORNIT® application technology department or the BORNIT® service hotline on +49 375 2795 123.

The product can be stored for 12 months in the original sealed container. Not sensitive to frost!

disposal note
Only recycle completely empty containers. Material residues can be disposed of according to AVV-ASN: 080409* (adhesive and sealing compound residues containing organic solvents or other hazardous substances).

The above information replaces all previous technical information about the product. Thus, this information is no longer valid. The details have been compiled according to the latest state of application technology. Please observe, however, that, depending on the state of the construction object, deviations from the method of application suggested in the datasheet may be required. Unless agreed otherwise in individual contracts, any information contained in the datasheet shall be non-binding and thus does not represent an agreed product constitution. We reserve the right to any changes in the information contained in this datasheet anytime.


Safety Data Sheet Poison Information Centre , 24h: +49-361-730730

ERFURT - Poison Control Centre Erfurt, Joint Poison Information Centre of the federal States of Mecklenburg-Western Pomerania, Saxony, Saxony-Anhalt and Thuringia; ggiz@ggiz-erfurt.de; www.ggiz-erfurt.de

-     What: name of the substance or product as precisely as possible, etc.
-     How much: as exact a quantity as possible
-     Who: Age, weight, sex and condition of the person(s) concerned.
-     When: Time of the event
-     Where: Place of occurrence
-     How: ingestion, inhalation, skin contact, etc.
-     Why: accidentally or intentionally


Kein Gefahrgut im Sinne der Transportvorschriften.

Hazard pictograms

signal word

Hazard-determining components for labelling
Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclics, <2% aromatics

H226: Flammable liquid and vapour.
H336: May cause drowsiness or dizziness.

EUH066: Repeated exposure may cause skin dryness or cracking.

P102: Keep out of reach of children.
P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P271: Use only outdoors or in a well-ventilated area.
P403 + P233: Store in a well-ventilated place. Keep container tightly closed.
P501: Dispose of contents/container to a suitable recycling or disposal facility.
P280: Wear protective gloves/protective clothing.

recommended, personal protective equipment: