BORNIT^® Asphalt Adhesive C40BF5-S

Status technical data sheet

01 December 2020

Areas of application

BORNIT^® Asphalt Adhesive C40BF5-S is used for spraying on soiled, aged or milled asphalt surfaces, which are prepared for the subsequent application of asphalt mix. It serves as a bonding agent for producing composite layers in asphalt construction. BORNIT^® Asphalt Adhesive C40BF5-S adheres well to all asphalt substrates.
BORNIT^® Asphalt Adhesive C40BF5-S is used for load classes Bk1,0 and Bk0,3.

Type and properties

BORNIT^® Asphalt Adhesive C40BF5-S is a special cationic bitumen emulsion with high wettability. Excellent adhesion on bituminous substrates is achieved through a small portion of fluxing agent. Due to its low viscosity, the product is finely sprayable in the cold state, too.

Advantages

Surface

Make sure that the substrate is firm, not wet and free from separating agents. Standing water must be removed.

Processing

Immediate processing after delivery is recommended.

Filling, storage and substrate temperature: min. 5 °C
Processing temperature: min. 20 °C – max. 50 °C

The line systems of transport and processing vehicles must be emptied following completion of work, if applicable. Longer transportation of the emulsion must be undertaken in full tanks. In order to avoid foaming of the product, filling or re-filling must be undertaken using bottom-up filling.
Spraying equipment used for application must be cleaned immediately after use in order to avoid clogging of nozzles and pipelines with bitumen. Such cleaning must be undertaken according to the provisions of the manufacturer of the spraying equipment. Do not mix BORNIT^® Asphalt Adhesive C40BF5-S with bitumen emulsions of other designations and other manufacturers.

Consumption

ca. 0,20 - 0,45 kg/m², gemäß Tabelle 8 der ZTV Asphalt-StB 07

Product type

bitumen adhesive

Base

road pavement bitumen

Solvent

water

Density at +20 °C

0.98 g/cm³

Consistency

liquid, homogeneous

Film-forming components

38 - 42 %

Colour(s)

black

Application

BORNIT^® Asphalt Adhesive Sprayer, Hand-operated spraying machine, ramp sprayer or the like

Processing temperature (ambient and substrate)

not below +5 °C and not above +30 °C

Cleaning

immediately with water, in the fully hardened state with BORNIT^® MultiClean Spray, BORNIT^® MultiClean or BORNIT^® Bitumen Cleaner

Storage

protect from frost!

Shelf life

in originally sealed containers storable for 4 weeks

GISCODE

BBP20

VOC category

Actual permissible VOC content

70 g/ltr.

Substances hazardous to health in terms of the ordinance on hazardous materials

none

Hazard class according to ADR

none

Flash point

n.b.

type of charge

cationic

sieve residue

max. 0.5 %

binder content

38-42 %

Health and fire protection, occupational safety

Please retrieve information regarding handling, safety and ecology from the current safety datasheet.

Storage

The product can be stored for 4 weeks. Prior to use or filling, briefly recirculate the adhesive. Suitable pumps are, e.g., channel impellers. Upon direct spraying from barrels, these should be rolled beforehand. BORNIT^® Asphalt Adhesive C40BF5-S is not frost-resistant!

Disposal note

Only recycle completely empty containers. Material residues can be disposed of according to AVV-ASN: 080410 (adhesive and sealing compound residues, except for those falling under 080409).

Note

The above information replaces all previous technical information about the product. Thus, this information is no longer valid. The details have been compiled according to the latest state of application technology. Please observe, however, that, depending on the state of the construction object, deviations from the method of application suggested in the datasheet may be required. Unless agreed otherwise in individual contracts, any information contained in the datasheet shall be non-binding and thus does not represent an agreed product constitution. We reserve the right to any changes in the information contained in this datasheet anytime.